Neo PowerLifts™
Strength
These compact yet powerful Rare Earth lift magnets can be used on flat or round surfaces and contain an internal release on/off device that does not contact or damage the surface of the part being lifted. Permanent magnetic lifts eliminate the fear of dropping the load being lifted due to power failures.
Efficient
Small, high-power permanent magnets require no external energy source. Two-person operation becomes a one-person operation.
Versatile
Lifts flat or round loads (see chart below).
Safety
PowerLift™ magnets feature a positive lock on and off. This locking feature is built into the handle that requires the operator to lock the magnet on and to lock the magnet off. This prevents the handle from being bumped partially on and give the operator a false feeling that the magnet is holding safely. The locking system is performed by first pulling on the handle to release the lock pin, than rotate the handle to the on position. To turn the magnet off requires the same step as turning the magnet on in the reverse direction. CONFORMS TO ASME B30.20 STANDARDS.
|
Dimensions (in inches) | |||||||
| Model |
Wgt (lbs) |
A | B | C | D | E | F |
| PNL220 | 7 | 3.625 | 5 | 2.625 | 2.625 | 6.625 | 5.875 |
| PNL660 | 22 | 6.375 | 7.875 | 3.625 | 3.875 | 8.875 | 6.875 |
| PNL1300 | 53 | 9.125 | 10.75 | 4.875 | 4.75 | 8.875 | 6.75 |
| PNL2200 | 110 | 10.625 | 12.625 | 7.125 | 6.5 | 8.875 | 10.125 |
| PNL4400 | 276 | 14.875 | 16.5 | 9.25 | 8.375 | 18 | 16.75 |
| PNL6600 | 485 | 18.0625 | 20 | 11.25 | 10.25 | 22.25 | 10.625 |
|
Holding Value & *Max. Sheet Length Due To Sag For Material Thickness | |||||||||
| Model | 1/4” (6’) | 3/8” (8’) | 1/2” (8’) | 3/4” (8’) | 1” (10’) | 2” (10’) | 3” (10’) | Round (lbs) | Min. Dia (inches) |
| PNL220 | 180 | 220 | 220 | 220 | 220 | 220 | 220 | 110 | 2 |
| PNL660 | 270 | 500 | 615 | 660 | 660 | 660 | 660 | 330 | 3 |
| PNL1300 | CF | CF | 800 | 1300 | 1300 | 1300 | 1300 | 650 | 4 |
| PNL2200 | NA | NA | CF | CF | 1490 | 2200 | 2200 | 1100 | 5 |
| PNL4400 | NA | NA | NA | NA | CF | 2625 | 4400 | 2200 | 14 |
| PNL6600 | NA | NA | NA | NA | NA | NA | 6600 | 3300 | CF |
NOTE: Holding Values for the PowerLift Magnets are stated at 33% of the actual value. We recommend when lifting sheets over 8' in length, use 2 or more lifts on a spreader bar to prevent sheet flexing, sagging or peel-off. Thin material is susceptible to magnetic bleed through, resulting in two sheets being lifted at once.
* These maximum sheet lengths are selected due to the sag characteristics of the specified sheet. The item to be lifted must cover the entire length and width of the magnetic poles to properly engage and release the part. CF = Consult Factory NA = Not Applicable ( Magnets listed will not turn “ON” on specified material thicknesses).
Round Item Holding Values are based on ideal conditions. Pipe length, wall thickness, diameter and surface condition can all effect the magnet’s performance. Please consult the factory before specifying these magnets for use on round materials.